The other option is to build a new Linux Kernel 4.11.x to make the single ATSC tuner work. Re: Fwd: em28xx: add support for Hauppauge WinTV-dualHD DVB tuner - Linux media You would have to wait future version of LibreELEC with a future Linux Kernel to see dual ATSC/DVB-C tuner support. You would have to wait for a future version of LibreELEC with a Linux Kernel of 4.11.x or greater to see ATSC tuner support. The single ATSC tuner support of the Hauppauge Wintv-Dual HD showed up in the newly released Linux Kernel 4.11.x. Sorry but LibreELEC version 8.0.2 with Linux Kernel 4.9.x does not support any ATSC tuner of the Hauppauge Wintv-Dual HD. It does nothing for the North American ATSC tuner version since it uses a LGDT3306a for its demodulator. That firmware is only for the Si2168-B40 demodulator on the DVB-C tuner version of the Hauppauge Wintv-Dual HD. I believe mine is ATSC as well, North American broadcast, correct? I also have the firmware in my lib/firmware folder. Modules linked in: si2157(O) lgdt3306a(O) i2c_mux em28xx_dvb(O+) dvb_core(O) 8021q xt_nat xt_tcpudp ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 xt_addrtype iptable_filter ip_tables xt_conntrack x_tables nf_nat nf_conntrack br_netfilter bridge stp llc overlay snd_hda_codec_hdmi rfcomm nvidia(PO) fuse bnep em28xx(O) v4l2_common(O) tveeprom(O) videodev(O) intel_powerclamp snd_hda_codec_realtek snd_hda_codec_generic btusb btrtl btbcm btintel firewire_ohci bluetooth firewire_core crc_itu_t rfkill snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep uvesafb

BUG: unable to handle kernel paging request at ffff8801b65e98b0 kernel tried to execute NX-protected page - exploit attempt? (uid: 0) lgdt3306a 2-0059: LG Electronics LGDT3306A successfully attached usb 1-5: em28174#1: Binding DVB extension Latest git patches (needed if you report a bug to

enough quality for its usage in production. As the driver is backported to an older kernel, it doesn't offer WARNING: You are using an experimental version of the media stack. usbcore: registered new interface driver em28xx usb 1-5: em28174#1: dvb ts2 set to isoc mode. usb 1-5: em28174#1: Identified as Hauppauge WinTV-dualHD ATSC (card=100) usb 1-5: em28174#1: microcode start address = 0x0004, boot configuration = 0x01 IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready ip_tables: (C) 2000-2006 Netfilter Core Team Update your scripts to load br_netfilter if you need this. bridge: filtering via arp/ip/ip6tables is no longer available by default. usb 1-5: em28174#0: dvb set to isoc mode. tveeprom: has no radio, has IR receiver, has no IR transmitter tveeprom: audio processor is None (idx 0) tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc) tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4) usb 1-5: em28174#0: Identified as Hauppauge WinTV-dualHD ATSC (card=100) usb 1-5: em28174#0: microcode start address = 0x0004, boot configuration = 0x01

Hauppauge wintv dualhd 01595 tv tuner